VICOM plans, supplies and installs LED displays in all common standard sizes as well as special constructions. Of course, we also take over the maintenance and technical service.
In addition, VICOM offers the appropriate control software.
The latest technologies and know-how are always used. Our customers can thus always be sure that the installations have the legal certifications.
The right LEDs for your application
There are many different LED configurations. Our requirement is to select the best one for your project from all possibilities.
First of all, it is important for the application to choose the optimal pixel pitch. If this is too large, the viewer can recognize the individual pixels, which leads to a negative image impression. If the pixel pitch is too small, the viewer will certainly not recognize individual pixels, but the system will be disproportionately expensive.
VICOM offers customized solutions for all applications. Thus, in addition to the usual RRGB configurations (picture above left), we also offer the modern RGB layout for outdoor use (upper middle picture). The advantage here is the increased contrast and the optimized cooling.
For indoor use SMD LEDs are used, these are often referred to as all-in-one LEDs. Their construction is extremely compact. The LEDs of the basic colors are integrated in a single small element. As a result, the pictures look extremely homogenous even at small distances. SMD LEDs can be manufactured to a minimum distance of 3 mm and thus achieve a high acceptance even in the conference room area.
In the SMD technique, the red, green and blue LEDs are shed in a small compact housing, so that a pixel is only visible as a single point.
These are sometimes used for outdoor walls. By using 2 red LEDs / pixels you can reach a very high light intensity. If the distance is sufficient, the eye no longer resolves the individual LEDs.
Stage shows often use strip displays. The strip arrangement of the LEDs makes the displays semi-transparent.
In contrast to the left module, special SMDs are used here. They are poured into a dark plastic. This increases the contrast.
This LED arrangement is used for outdoor or indoor walls. The LEDs are smaller than in the left example. The additional black background area creates a higher contrast.
The right housing for your application
VICOM offers the best for your application from a variety of housings and housing variants.
Our different housing designs ensure the greatest possible flexibility. This concerns first of all the different sizes. The standard version is made of steel, alternatively aluminum is often available for a surcharge. Outer casings are approved with special seals IP65. Depending on the purpose, the housing can be made adjustable and / or dependent.
In the rental area mainly Slim-Line housings are used, because their low weight makes the handling very easy and a crane is often superfluous. For window inserts, our eco-housings are preferred. They are heavier than the other models, but they are unbeatable in price. Brightness sensors can be integrated to minimize power consumption.
This case has no fans and therefore allows noiseless use in opera, drama, foyer, etc. With only 8 kg and quick-release mechanisms, silent enclosures are easy to assemble.
Stage shows use strip casings. The strip arrangement of the LEDs makes the displays semi-transparent. They are also ideal for façade applications, as they are cost-effective.
The housing made of sheet steel is mainly used for fixed installations. Eco is the most cost-effective housing.
This housing is made of die-cast aluminum and is therefore particularly torsionally rigid and lightweight. Quick-release fasteners make construction a lot easier.
These can be easily detected at this stage and repaired at no high cost. Then of course it goes again in the 48 hours endurance test. Subsequently, the modules are installed in the housing. The contact security within each individual housing is then confirmed on a vibrating table. Finally, the IP-65 water resistance is checked in a dip tank. When all stages of production have been completed, all LED walls are subjected to a final 48 hour total test under real conditions.
All walls are built in original size and tested as a complete unit with video playback. A clean and expertly perfect execution is the basis for a perfectly functioning system. Of course, maintenance contracts can be concluded at any time for VICOM LED walls, so that the customer always has the certainty of a top-maintained facility.
Production of LED displays (5: 11)
- Quality Assurance
- 72 hours endurance test of the individual components
- State-of-the-art production facilities
- 48 hours Endurance test of the assembled LED displays
- Integration and installation
- Planning and service
LED indoor installation (2: 00)